home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
Shareware Overload Trio 2
/
Shareware Overload Trio Volume 2 (Chestnut CD-ROM).ISO
/
dir39
/
2000tech.zip
/
1101.TXT
< prev
next >
Wrap
Text File
|
1993-06-15
|
4KB
|
123 lines
Document Number 1101
Mouse Parameters for version 6.2x:
12/30/92
Basic parameters for all mice:
*Ballistic Effect*
BHIGH - Sets the ballistic effect to high.
BLOW - Sets the ballistic effect to low.
BON - Turns the ballistic effect on.
BOFF - Turns the ballistic effect off.
*Sensitivity*
S00-S10 - Set the degree of sensitivity for the mouse.
(example MOUSE S06 or MOUSE S09)
*Button Swap*
SWAP - Toggles the left and right mouse button functionality.
MSWAP - Toggles the middle and right mouse button functionality.
NOTE: For TrackMan Portable users, left button corresponds
to top button and right button corresponds to the
bottom button.
*Parameters*
/? - Lists some of the mouse parameters and their description
*Status*
? - The status parameter displays the current mouse driver
settings.
*Number of Buttons*
2K - Sets the middle mouse button to act like a Left-Right button
3K - Sets the middle mouse button to act as a separate button.
*Cursor Enhancement*
Cenhance- Loads cursor enhancements with default settings.
NOTE: This parameter will only work when first loading the
mouse driver.
CSLOW - Sets text mouse cursor to blink slow.
CFAST - Sets text mouse cursor to blink fast.
COFF - Sets text mouse cursor not to blink.
LCURSOR - Displays hardware text cursor with a rectangular block, and
displays the graphics with a reverse video block.
DCURSOR - Disables lcursor.
TON - Displayed hardware and software text cursor with a tail.
TOFF - Disables the tail.
*Drag-Lock*
DLEFT - Sets the left or top button for drag-lock.
DRIGHT - Sets the right or bottom button for drag-lock.
DNONE - Disables drag-lock.
*Remove from Memory*
OUT - Removes the mouse driver from memory.
NOTE: If you use the OUT parameter, you must remove MOUSE,
LOGIMENU, and CLICK in the reverse order that you
load them.
*Type*
Note: These parameters will work only when first loading
the mouse driver in memory.
BUS - Forces the driver to look at the bus port.
PS2 - Forces the driver to look at the PS/2 port.
SER - Forces the driver to look at the serial port.
1 - Configures the mouse for COM port 1.
2 - Configures the mouse for COM port 2.
Mouse Driver Parameters for SERIAL MICE:
NOTE: Parameters with a "C" in parenthesis will work with the
Series 7 and 9 type mouse. Parameters with an "M" in
parenthesis will work with Series M mice. Type MOUSE ?
to find out which type of mouse is being used.
*Report Rate*
10 (C) - Sets the report rate (signal per second from the mouse to the
computer) to 10.
50 (C) - Sets the report rate to 50.
150 (C) - Sets the report rate to 150.
*Baud Rate*
1200 (C)- Sets the report rate (information exchange rate between the mouse
and the computer) to 1200.
2400 (C)- Sets the baud rate to 2400.
4800 (C)- Sets the baud rate to 4800.
9600 (C)- Sets the baud rate to 9600.
*Protocol*
MM (C) - Sets the protocol (data tranmission regulator) for MM Series mouse.
5b (C) - Sets the protocol for 5-byte packed binary.
RE (C) - Sets the protocol for relative bit pad one.
MI (M) - Sets the protocol to two-button Microsoft compatible three-byte
format.
MP (M) - Sets the protocol to three-button Microsoft compatible four-byte
format.
*Inital Settings*
INIT - Resets the mouse driver
(M) Cordless - Report 100, Baud 9600, Protocol MP.
(M) - Report 100, Baud 1200, Protocol MP.
(C) - Report 150, Baud 2400, Protocol MM.